العربية
中国
Français
Deutsch
Ελληνική
हिन्दी
Italiano
日本語
Português
Русский
EspañolHARD WATER
'Hard water' is water that has a high mineral content (water with a low mineral content is known as ''soft water''). This content usually consists of high levels of metal ions, mainly calcium (Ca2+) and magnesium (Mg2+) in the form of carbonates, but may include several other metals as well as bicarbonates and sulfates. It is not generally dangerous. The simplest way to determine if water is hard or soft is the lather/froth test. If the water is very soft, soap will tend to lather up easily when agitated, whereas with hard water it will not. Toothpaste will also not froth well in hard water. More exact methods of 'hardness' detection use a wet titration method to determine hardness.
Total water 'hardness' (including both Ca2+ and Mg2+ ions) is reported as ppm w/v (or mg/L) of calcium carbonate (CaCO3). Water hardness usually measures the total concentration of calcium and magnesium, the two most prevalent divalent metal ions, although in some geographical locations iron, aluminium, and manganese may also be present at elevated levels. Calcium usually enters the water as either calcium carbonate (CaCO3), from limestone or chalk, or from mineral deposits of calcium sulfate (CaSO4). The predominant source of magnesium is dolomite (CaMg(CO3)2).
A common distinction is made between 'temporary' and 'permanent' hardness. There are also common types of hard water depending on the ion (eg. Mg or Ca) found in the water.
Temporary hardness is hardness that can be removed by boiling or by the addition of lime (calcium hydroxide). It is caused by a combination of calcium ions and bicarbonate ions in the water. Boiling, which promotes the formation of carbonate from the bicarbonate, will precipitate calcium carbonate out of solution, leaving water that is less hard on cooling.
The following is the equilibrium reaction when calcium carbonate (CaCO3) is "dissolved" in water:
Upon heating, less CO2 is able to dissolve into the water (see Solubility). Since there is not enough CO2 around, the reaction cannot proceed from left to right, and therefore the CaCO3 will not "dissolve" as readily. Instead, the reaction is forced to go from right to left (i.e. products to reactants) to reestablish equilibrium, and solid CaCO3 is formed. Heating water will remove hardness as long as the solid CaCO3 that precipitates out is removed. After cooling, if enough time passes the water will pick up CO2 from the air and the reaction will again proceed from left to right, allowing the CaCO3 to "redissolve" in the water.
For considerably more detail on the solubility of calcium carbonate in water, and how it is affected by atmospheric carbon dioxide, please see the calcium carbonate article.
Permanent hardness is hardness (mineral content) that cannot be removed by boiling. It is usually caused by the presence of calcium and magnesium sulfates and/or chlorides in the water, which become more soluble as the temperature rises. Despite the name this can be removed using a water softener, or ion exchange column.
Hard water causes scaling, which is the precipitation of minerals to form a deposit called limescale. Scale can clog pipes and can decrease the life of toilet flushing units. It can coat the inside of tea and coffee pots, and clog and ruin water heaters.
Similarly, the insoluble salts that get left behind from using regular shampoo in hard water tend to leave hair rougher and harder to detangle. [1]
In industry, hard water contributes to scaling in boilers, cooling towers and other industrial equipment. In these industrial settings, water hardness must be constantly monitored to avoid costly breakdowns. Hardness is controlled by addition of chemicals and by large-scale softening with zeolite resins and ion exchange resins.
It is possible to measure the level of hard water by obtaining a free water testing kit. These are supplied by most water softening companies. There are several different scales used to describe the hardness of water in different contexts.
★ mmol/L (millimoles per litre)
★ mg/L calcium carbonate equivalent
★ grains/gallon (gpg)
1 gr/U.S. gal = 17.11 mg/L
★ parts per million weight/volume (ppm ''w''/''v'' or ppm ''m''/''v'')
★ Various obsolete "degrees":
★
★ Clark degrees (°Clark)/English degrees (°E)
- conversion to mg/L calcium: divide by 0.175
One degree Clark corresponds to one grain of calcium carbonate in one Imperial gallon of water which is equivalent to 14.28 parts calcium carbonate in 1,000,000 parts water.
★
★ German degrees (°dH)
- conversion to mg/L calcium: divide by 0.14
One degree German corresponds to one part calcium oxide in 100,000 parts of water.
★
★ French degrees (°f) (shares symbol with degree Fahrenheit, but in lowercase)
- conversion to mg/L calcium: divide by 0.25
One degree French corresponds to one part calcium carbonate in 100,000 parts of water.
★
★ American degrees
One degree American corresponds to one part calcium carbonate in 1,000,000 parts water (1 mg/L or 1 ppm)
★
★ Degrees of general hardness (dGH)
One degree of general hardness corresponds to 10 mg of calcium oxide or magnesium oxide per litre of water
The precise mixture of minerals dissolved in the water, together with the water's acidity or alkalinity (pH) and temperature will determine the behaviour of the hardness, so single number on a scale does not give a full description. Descriptions of hardness correspond roughly with ranges of mineral concentrations:
★ Soft: 0 - 20 mg/L as calcium
★ Moderately soft: 20 - 40 mg/L as calcium
★ Slightly hard: 40 - 60 mg/L as calcium
★ Moderately hard: 60 - 80 mg/L as calcium
★ Hard: 80 - 120 mg/L as calcium
★ Very Hard >120 mg/L as calcium
Several indices are used to describe the behaviour of calcium carbonate in water, or in water, oil and gas mixtures.[2]
===Langelier Saturation Index (LSI)===
The Langelier Saturation Index (LSI) (sometimes also Langelier ''Stability'' Index) is a calculated number used to predict the calcium carbonate stability of water; that is, whether a water will precipitate, dissolve, or be in equilibrium with calcium carbonate. Langelier developed a method for predicting the pH at which water is saturated in calcium carbonate (called pHs). The LSI is expressed as the difference between the actual system pH and the saturation pH.
LSI = pH - pHs
If the actual pH of the water is below the calculated saturation pH, the LSI is negative and the water has a very limited scaling potential. If the actual pH exceeds pHs, the LSI is positive, and being supersaturated with CaCO3, the water has a tendency to form scale. At increasing positive index values, the scaling potential increases.
===Ryznar Stability Index (RSI)
Puckorius Scaling Index (PSI)
Other indices===
Other indices used include the Larson-Skold Index[3], the Stiff-Davis Index[4], and the Oddo-Tomson Index[5].
The World Health Organization says, "There does not appear to be any convincing evidence that water hardness causes adverse health effects in humans."[6]
Some studies have shown a weak inverse relationship between water hardness and cardiovascular disease in men, up to a level of 170 mg calcium carbonate per liter of water. The World Health Organization has reviewed the evidence and concluded the data were inadequate to allow for a recommendation for a level of hardness.6
In a review by František Kožíšek, M.D., Ph.D. National Institute of Public Health, Czech Republic gives a good overview of the topic, and unlike the WHO, sets some recommendations for the maximum and minimum levels of calcium (40-80 mg/L) and magnesium (20-30 mg/L) in drinking water, and a total hardness expressed as the sum of the calcium and magnesium concentrations of 2-4 mmol/L.[7]
Other studies have shown weak correlations between cardiovascular health and water hardness.[8][9][10]
Very soft water can corrode the metal pipes in which it is carried and as a result the water may contain elevated levels of cadmium, copper, lead and zinc [6].
It is often desirable to soften hard water, as it does not readily form lather with soap. Soap is wasted when trying to form lather, and in the process, scum forms. Hard water may be treated to reduce the effects of scaling and to make it more suitable for laundry and bathing.
A water softener works on the principle of cation or ion exchange in which ions of the hardness minerals are exchanged for sodium or potassium ions, effectively reducing the concentration of hardness minerals to tolerable levels.[12]
The most economical way to soften household water is with an ion exchange water softener. This unit uses sodium chloride (table salt) to recharge beads made of ion exchange resin that exchange hardness mineral ions for sodium ions. Artificial or natural zeolites can also be used. As the hard water passes through and around the beads, the hardness mineral ions are preferentially absorbed, displacing the sodium ions. This process is called ion exchange. When the bead or sodium zeolite has a low concentration of sodium ions left, it is exhausted, and can no longer soften water. The resin is recharged by flushing (often ''back''-flushing) with saltwater. The high excess concentration of sodium ions alter the equilibrium between the ions in solution and the ions held on the surface of the resin, resulting in replacement of the hardness mineral ions on the resin or zeolite with sodium ions. The resulting saltwater and mineral ion solution is then rinsed away, and the resin is ready to start the process all over again. This cycle can be repeated many times.
Some softening processes in industry use the same method, but on a much larger scale. These methods create an enormous amount of salty water that is costly to treat and dispose of.
Temporary hardness, caused by hydrogen carbonate (or bicarbonate) ions, can be removed by boiling. For example, calcium hydrogen carbonate, often present in temporary hard water, is boiled in a kettle to remove the hardness. In the process, a scale forms on the inside of the kettle in a process known as "furring of kettles". This scale is composed of calcium carbonate.
Ca(HCO3)2 → CaCO3 + CO2 + H2O
Hardness can also be reduced with a lime-soda ash treatment. This process, developed by Thomas Clark in 1841, involves the addition of slaked lime (calcium hydroxide — Ca(OH)2) to a hard water supply to convert the hydrogen carbonate hardness to carbonate, which precipitates and can be removed by filtration:
Ca(HCO3)2 + Ca(OH)2 → 2CaCO3 + 2H2O
The addition of sodium carbonate also softens permanently hard water containing calcium sulfate, as the calcium ions form calcium carbonate which precipitates out and sodium sulfate is formed which is soluble. The calcium carbonate formed sinks to the bottom. Sodium sulfate has no effect on the hardness of water.
Na2CO3 + CaSO4 → Na2SO4 + CaCO3
Some confusion may arise after a first experience with soft water. Hard water does not lather well with soap and leaves a "less than clean" feeling. Soft water lathers better than hard water but leaves a "slippery feeling" on the skin after use with soap. For example, a certain water softener manufacturer contests that the "slippery feeling" after showering in soft water is due to "cleaner skin" and the absence of "friction-causing" soap scum.
However, the chemical explanation is that soft water, due to its sodium content, has a much reduced ability to combine with the soap film on your body and therefore, it is much more difficult to rinse off.[13] Solutions are to use less soap or a synthetic liquid body wash.
Analysis of water hardness in major Australian cities by the Australian Water Association shows a range from very soft (Melbourne) to very hard (Adelaide).
Total Hardness as Calcium Carbonate mg/L are:
Canberra: 40[14]; Melbourne: 10 - 26[15];
Sydney: 39.4 - 60.1[16];
Perth: 29 - 226[17];
Brisbane: 100[18];
Adelaide: 134 - 148[19];
Hobart: 5.8 - 34.4[20];
Darwin: 31[21].
Prairie provinces (mainly Saskatchewan and Manitoba) contain high quantities of calcium and magnesium, often as dolomite, which are readily soluble in the groundwater that contains high concentrations of trapped carbon dioxide from the last glaciation. In these parts of Canada, the total hardness in mg/L calcium carbonate equivalent frequently exceeds 200 mg/L, if groundwater is the only source of potable water.
Some typical values are: Calgary 165 mg/L, Saskatoon < 140 mg/L, Toronto 121 mg/L,[22] Vancouver < 5 mg/L , Charlottetown PEI 140 - 150 mg/L.[23]
Information from the British Drinking Water Inspectorate shows that drinking water in England is generally considered to be 'very hard', with most areas of England, particularly the East, exhibiting above 200 mg/L as calcium carbonate equivalent. Wales, Devon, Cornwall and parts of North-West England are softer water areas, and range from 0 to 200 mg/L . In the brewing industry in England and Wales, water is often deliberately hardened with gypsum in the process of Burtonisation.
According to the United States Geological Survey, 89.3% of US homes have hard water. The softest waters occur in parts of the New England, South Atlantic-Gulf, Pacific Northwest, and Hawaii regions. Moderately hard waters are common in many of the rivers of the Tennessee, Great Lakes, Pacific Northwest, and Alaska regions. Hard and very hard waters are found in some of the streams in most of the regions throughout the country. Hardest waters (greater than 1,000 mg/L) are in streams in Texas, New Mexico, Kansas, Arizona, and southern California.[24]
★ Water softener
★ Water quality
★ Water treatment
★ Water purification
''Note: Hard water should not be confused with heavy water.''
1. Body And Fitness Healthy Hair Tips
2. http://64.224.111.143/technicallibrary/corrdoctors/Modules/NaturalWaters/Frames.htm
3. T.E., Larson and R. V. Skold, Laboratory Studies Relating Mineral Quality of Water to Corrosion of Steel and Cast Iron, 1958 Illinois State Water Survey, Champaign, IL pp. [43] - 46: ill. ISWS C-71
4. Stiff, Jr., H.A., Davis, L.E., A Method For Predicting The Tendency of Oil Field Water to Deposit Calcium Carbonate, Pet. Trans. AIME 195;213 (1952).
5. Oddo,J.E., Tomson, M.B.,Scale Control, Prediction and Treatment Or How Companies Evaluate A Scaling Problem and What They Do Wrong, CORROSION/92, Paper No. 34, (Houston, TX:NACE INTERNATIONAL 1992).
6. World Health Organization Hardness in Drinking-Water, 2003
7. František Kožíšek Health significance of drinking water calcium and magnesium, February 2003
8. http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=pubmed&cmd=Retrieve&dopt=AbstractPlus&list_uids=7233165&query_hl=8&itool=pubmed_docsum
9. http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?itool=abstractplus&db=pubmed&cmd=Retrieve&dopt=abstractplus&list_uids=12803370
10. http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?itool=abstractplus&db=pubmed&cmd=Retrieve&dopt=abstractplus&list_uids=9888277
11. World Health Organization Hardness in Drinking-Water, 2003
12. How does a water softener work? at Howstuffworks.com
13. With soft water, why can't we rinse off all the soap?
14. ACTewAGL: Dishwashers and Water Hardness
15. Melbourne Water Public Health Compliance Report - July-September 2006
16. Sydney Typical Drinking Water Analysis
17. Perth Drinking Water Quality Annual report 2005-06
18. Brisbane Drinking Water
19. Adelaide Water Quality
20. Hobart Drinking Water Quality
21. Darwin Water Quality
22. City of Toronto: Toronto Water - FAQ
23. [1]
24. Briggs, J.C., and Ficke, J.F.; ''Quality of Rivers of the United States, 1975 Water Year -- Based on the National Stream Quality Accounting Network (NASQAN)'': U.S. Geological Survey Open-File Report 78-200, 436 p. (1977)
★ Alcoa Chemical, Langelier Saturation Index (LSI) Calculator
Total water 'hardness' (including both Ca2+ and Mg2+ ions) is reported as ppm w/v (or mg/L) of calcium carbonate (CaCO3). Water hardness usually measures the total concentration of calcium and magnesium, the two most prevalent divalent metal ions, although in some geographical locations iron, aluminium, and manganese may also be present at elevated levels. Calcium usually enters the water as either calcium carbonate (CaCO3), from limestone or chalk, or from mineral deposits of calcium sulfate (CaSO4). The predominant source of magnesium is dolomite (CaMg(CO3)2).
Types of hard water
A common distinction is made between 'temporary' and 'permanent' hardness. There are also common types of hard water depending on the ion (eg. Mg or Ca) found in the water.
Temporary hardness
Temporary hardness is hardness that can be removed by boiling or by the addition of lime (calcium hydroxide). It is caused by a combination of calcium ions and bicarbonate ions in the water. Boiling, which promotes the formation of carbonate from the bicarbonate, will precipitate calcium carbonate out of solution, leaving water that is less hard on cooling.
The following is the equilibrium reaction when calcium carbonate (CaCO3) is "dissolved" in water:
Upon heating, less CO2 is able to dissolve into the water (see Solubility). Since there is not enough CO2 around, the reaction cannot proceed from left to right, and therefore the CaCO3 will not "dissolve" as readily. Instead, the reaction is forced to go from right to left (i.e. products to reactants) to reestablish equilibrium, and solid CaCO3 is formed. Heating water will remove hardness as long as the solid CaCO3 that precipitates out is removed. After cooling, if enough time passes the water will pick up CO2 from the air and the reaction will again proceed from left to right, allowing the CaCO3 to "redissolve" in the water.
For considerably more detail on the solubility of calcium carbonate in water, and how it is affected by atmospheric carbon dioxide, please see the calcium carbonate article.
Permanent hardness
Permanent hardness is hardness (mineral content) that cannot be removed by boiling. It is usually caused by the presence of calcium and magnesium sulfates and/or chlorides in the water, which become more soluble as the temperature rises. Despite the name this can be removed using a water softener, or ion exchange column.
Problems caused by hard water
Hard water causes scaling, which is the precipitation of minerals to form a deposit called limescale. Scale can clog pipes and can decrease the life of toilet flushing units. It can coat the inside of tea and coffee pots, and clog and ruin water heaters.
Similarly, the insoluble salts that get left behind from using regular shampoo in hard water tend to leave hair rougher and harder to detangle. [1]
In industry, hard water contributes to scaling in boilers, cooling towers and other industrial equipment. In these industrial settings, water hardness must be constantly monitored to avoid costly breakdowns. Hardness is controlled by addition of chemicals and by large-scale softening with zeolite resins and ion exchange resins.
Types of measurement
It is possible to measure the level of hard water by obtaining a free water testing kit. These are supplied by most water softening companies. There are several different scales used to describe the hardness of water in different contexts.
★ mmol/L (millimoles per litre)
★ mg/L calcium carbonate equivalent
★ grains/gallon (gpg)
1 gr/U.S. gal = 17.11 mg/L
★ parts per million weight/volume (ppm ''w''/''v'' or ppm ''m''/''v'')
★ Various obsolete "degrees":
★
★ Clark degrees (°Clark)/English degrees (°E)
- conversion to mg/L calcium: divide by 0.175
One degree Clark corresponds to one grain of calcium carbonate in one Imperial gallon of water which is equivalent to 14.28 parts calcium carbonate in 1,000,000 parts water.
★
★ German degrees (°dH)
- conversion to mg/L calcium: divide by 0.14
One degree German corresponds to one part calcium oxide in 100,000 parts of water.
★
★ French degrees (°f) (shares symbol with degree Fahrenheit, but in lowercase)
- conversion to mg/L calcium: divide by 0.25
One degree French corresponds to one part calcium carbonate in 100,000 parts of water.
★
★ American degrees
One degree American corresponds to one part calcium carbonate in 1,000,000 parts water (1 mg/L or 1 ppm)
★
★ Degrees of general hardness (dGH)
One degree of general hardness corresponds to 10 mg of calcium oxide or magnesium oxide per litre of water
The precise mixture of minerals dissolved in the water, together with the water's acidity or alkalinity (pH) and temperature will determine the behaviour of the hardness, so single number on a scale does not give a full description. Descriptions of hardness correspond roughly with ranges of mineral concentrations:
★ Soft: 0 - 20 mg/L as calcium
★ Moderately soft: 20 - 40 mg/L as calcium
★ Slightly hard: 40 - 60 mg/L as calcium
★ Moderately hard: 60 - 80 mg/L as calcium
★ Hard: 80 - 120 mg/L as calcium
★ Very Hard >120 mg/L as calcium
Indices
Several indices are used to describe the behaviour of calcium carbonate in water, or in water, oil and gas mixtures.[2]
===Langelier Saturation Index (LSI)===
The Langelier Saturation Index (LSI) (sometimes also Langelier ''Stability'' Index) is a calculated number used to predict the calcium carbonate stability of water; that is, whether a water will precipitate, dissolve, or be in equilibrium with calcium carbonate. Langelier developed a method for predicting the pH at which water is saturated in calcium carbonate (called pHs). The LSI is expressed as the difference between the actual system pH and the saturation pH.
LSI = pH - pHs
If the actual pH of the water is below the calculated saturation pH, the LSI is negative and the water has a very limited scaling potential. If the actual pH exceeds pHs, the LSI is positive, and being supersaturated with CaCO3, the water has a tendency to form scale. At increasing positive index values, the scaling potential increases.
===Ryznar Stability Index (RSI)
The Ryznar stability index (RSI) uses a database of scale thickness measurements in municipal water systems to try and predict the effect of particular water chemistry.
Puckorius Scaling Index (PSI)
The Puckorius Scaling Index (PSI) uses slightly different parameters to quantify the relationship between the saturation state of the water and the amount of limescale deposited.
Other indices===Other indices used include the Larson-Skold Index[3], the Stiff-Davis Index[4], and the Oddo-Tomson Index[5].
Health considerations
The World Health Organization says, "There does not appear to be any convincing evidence that water hardness causes adverse health effects in humans."[6]
Some studies have shown a weak inverse relationship between water hardness and cardiovascular disease in men, up to a level of 170 mg calcium carbonate per liter of water. The World Health Organization has reviewed the evidence and concluded the data were inadequate to allow for a recommendation for a level of hardness.6
In a review by František Kožíšek, M.D., Ph.D. National Institute of Public Health, Czech Republic gives a good overview of the topic, and unlike the WHO, sets some recommendations for the maximum and minimum levels of calcium (40-80 mg/L) and magnesium (20-30 mg/L) in drinking water, and a total hardness expressed as the sum of the calcium and magnesium concentrations of 2-4 mmol/L.[7]
Other studies have shown weak correlations between cardiovascular health and water hardness.[8][9][10]
Very soft water can corrode the metal pipes in which it is carried and as a result the water may contain elevated levels of cadmium, copper, lead and zinc [6].
Softening
It is often desirable to soften hard water, as it does not readily form lather with soap. Soap is wasted when trying to form lather, and in the process, scum forms. Hard water may be treated to reduce the effects of scaling and to make it more suitable for laundry and bathing.
Process
A water softener works on the principle of cation or ion exchange in which ions of the hardness minerals are exchanged for sodium or potassium ions, effectively reducing the concentration of hardness minerals to tolerable levels.[12]
The most economical way to soften household water is with an ion exchange water softener. This unit uses sodium chloride (table salt) to recharge beads made of ion exchange resin that exchange hardness mineral ions for sodium ions. Artificial or natural zeolites can also be used. As the hard water passes through and around the beads, the hardness mineral ions are preferentially absorbed, displacing the sodium ions. This process is called ion exchange. When the bead or sodium zeolite has a low concentration of sodium ions left, it is exhausted, and can no longer soften water. The resin is recharged by flushing (often ''back''-flushing) with saltwater. The high excess concentration of sodium ions alter the equilibrium between the ions in solution and the ions held on the surface of the resin, resulting in replacement of the hardness mineral ions on the resin or zeolite with sodium ions. The resulting saltwater and mineral ion solution is then rinsed away, and the resin is ready to start the process all over again. This cycle can be repeated many times.
Some softening processes in industry use the same method, but on a much larger scale. These methods create an enormous amount of salty water that is costly to treat and dispose of.
Temporary hardness, caused by hydrogen carbonate (or bicarbonate) ions, can be removed by boiling. For example, calcium hydrogen carbonate, often present in temporary hard water, is boiled in a kettle to remove the hardness. In the process, a scale forms on the inside of the kettle in a process known as "furring of kettles". This scale is composed of calcium carbonate.
Ca(HCO3)2 → CaCO3 + CO2 + H2O
Hardness can also be reduced with a lime-soda ash treatment. This process, developed by Thomas Clark in 1841, involves the addition of slaked lime (calcium hydroxide — Ca(OH)2) to a hard water supply to convert the hydrogen carbonate hardness to carbonate, which precipitates and can be removed by filtration:
Ca(HCO3)2 + Ca(OH)2 → 2CaCO3 + 2H2O
The addition of sodium carbonate also softens permanently hard water containing calcium sulfate, as the calcium ions form calcium carbonate which precipitates out and sodium sulfate is formed which is soluble. The calcium carbonate formed sinks to the bottom. Sodium sulfate has no effect on the hardness of water.
Na2CO3 + CaSO4 → Na2SO4 + CaCO3
Why does my skin feel slippery after washing with softened water, unlike hard water?
Some confusion may arise after a first experience with soft water. Hard water does not lather well with soap and leaves a "less than clean" feeling. Soft water lathers better than hard water but leaves a "slippery feeling" on the skin after use with soap. For example, a certain water softener manufacturer contests that the "slippery feeling" after showering in soft water is due to "cleaner skin" and the absence of "friction-causing" soap scum.
However, the chemical explanation is that soft water, due to its sodium content, has a much reduced ability to combine with the soap film on your body and therefore, it is much more difficult to rinse off.[13] Solutions are to use less soap or a synthetic liquid body wash.
Regional Information
Hard water in Australia
Analysis of water hardness in major Australian cities by the Australian Water Association shows a range from very soft (Melbourne) to very hard (Adelaide).
Total Hardness as Calcium Carbonate mg/L are:
Canberra: 40[14]; Melbourne: 10 - 26[15];
Sydney: 39.4 - 60.1[16];
Perth: 29 - 226[17];
Brisbane: 100[18];
Adelaide: 134 - 148[19];
Hobart: 5.8 - 34.4[20];
Darwin: 31[21].
Hard water in Canada
Prairie provinces (mainly Saskatchewan and Manitoba) contain high quantities of calcium and magnesium, often as dolomite, which are readily soluble in the groundwater that contains high concentrations of trapped carbon dioxide from the last glaciation. In these parts of Canada, the total hardness in mg/L calcium carbonate equivalent frequently exceeds 200 mg/L, if groundwater is the only source of potable water.
Some typical values are: Calgary 165 mg/L, Saskatoon < 140 mg/L, Toronto 121 mg/L,[22] Vancouver < 5 mg/L , Charlottetown PEI 140 - 150 mg/L.[23]
Hard water in England and Wales
Information from the British Drinking Water Inspectorate shows that drinking water in England is generally considered to be 'very hard', with most areas of England, particularly the East, exhibiting above 200 mg/L as calcium carbonate equivalent. Wales, Devon, Cornwall and parts of North-West England are softer water areas, and range from 0 to 200 mg/L . In the brewing industry in England and Wales, water is often deliberately hardened with gypsum in the process of Burtonisation.
Hard water in the US
According to the United States Geological Survey, 89.3% of US homes have hard water. The softest waters occur in parts of the New England, South Atlantic-Gulf, Pacific Northwest, and Hawaii regions. Moderately hard waters are common in many of the rivers of the Tennessee, Great Lakes, Pacific Northwest, and Alaska regions. Hard and very hard waters are found in some of the streams in most of the regions throughout the country. Hardest waters (greater than 1,000 mg/L) are in streams in Texas, New Mexico, Kansas, Arizona, and southern California.[24]
See also
★ Water softener
★ Water quality
★ Water treatment
★ Water purification
''Note: Hard water should not be confused with heavy water.''
References
1. Body And Fitness Healthy Hair Tips
2. http://64.224.111.143/technicallibrary/corrdoctors/Modules/NaturalWaters/Frames.htm
3. T.E., Larson and R. V. Skold, Laboratory Studies Relating Mineral Quality of Water to Corrosion of Steel and Cast Iron, 1958 Illinois State Water Survey, Champaign, IL pp. [43] - 46: ill. ISWS C-71
4. Stiff, Jr., H.A., Davis, L.E., A Method For Predicting The Tendency of Oil Field Water to Deposit Calcium Carbonate, Pet. Trans. AIME 195;213 (1952).
5. Oddo,J.E., Tomson, M.B.,Scale Control, Prediction and Treatment Or How Companies Evaluate A Scaling Problem and What They Do Wrong, CORROSION/92, Paper No. 34, (Houston, TX:NACE INTERNATIONAL 1992).
6. World Health Organization Hardness in Drinking-Water, 2003
7. František Kožíšek Health significance of drinking water calcium and magnesium, February 2003
8. http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=pubmed&cmd=Retrieve&dopt=AbstractPlus&list_uids=7233165&query_hl=8&itool=pubmed_docsum
9. http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?itool=abstractplus&db=pubmed&cmd=Retrieve&dopt=abstractplus&list_uids=12803370
10. http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?itool=abstractplus&db=pubmed&cmd=Retrieve&dopt=abstractplus&list_uids=9888277
11. World Health Organization Hardness in Drinking-Water, 2003
12. How does a water softener work? at Howstuffworks.com
13. With soft water, why can't we rinse off all the soap?
14. ACTewAGL: Dishwashers and Water Hardness
15. Melbourne Water Public Health Compliance Report - July-September 2006
16. Sydney Typical Drinking Water Analysis
17. Perth Drinking Water Quality Annual report 2005-06
18. Brisbane Drinking Water
19. Adelaide Water Quality
20. Hobart Drinking Water Quality
21. Darwin Water Quality
22. City of Toronto: Toronto Water - FAQ
23. [1]
24. Briggs, J.C., and Ficke, J.F.; ''Quality of Rivers of the United States, 1975 Water Year -- Based on the National Stream Quality Accounting Network (NASQAN)'': U.S. Geological Survey Open-File Report 78-200, 436 p. (1977)
External Links
★ Alcoa Chemical, Langelier Saturation Index (LSI) Calculator
This article provided by Wikipedia. To edit the contents of this article, click here for original source.
psst.. try this: add to faves
