العربية
中国
Français
Deutsch
Ελληνική
हिन्दी
Italiano
日本語
Português
Русский
Español
Title:
Engine Running On Plasma Ignition-2 (Gasoline)
Description:
In this video I used no relay, no reed switch, and no car coil ignition. I used what Tero suggested in a yahoo forum. 220 Volt from rectifier connected directly to 47 uF 250 volt and spark plug. Ignition switching by original engine's ignition spark. The spark result is the same as my previous video because the same capasitor used. Engine with 100% gasoline runs with more power even though in fully closed carb throttle valve.
Author:
revizal
Tags:
swa-plasma, ignition, water, fuel,
Engine Running On Plasma Ignition-2 (Gasoline)
Description:
In this video I used no relay, no reed switch, and no car coil ignition. I used what Tero suggested in a yahoo forum. 220 Volt from rectifier connected directly to 47 uF 250 volt and spark plug. Ignition switching by original engine's ignition spark. The spark result is the same as my previous video because the same capasitor used. Engine with 100% gasoline runs with more power even though in fully closed carb throttle valve.
Author:
revizal
Tags:
swa-plasma, ignition, water, fuel,
Popular searches: Cuba, Scuba Diving, Skydiving, Dubai, Niagara Falls, Rainforest, Surfing, Snowboarding, Sandboarding, Pyramids, Everest, Stonehenge, Bear Grylls
Related Videos:
 | swa-plasma on gasoline engine (real appl test) I've completed the test of gasoline engine on real home application. The fuel consumption is 1 liter gasoline for 75 minutes. This's 73% saving compared to original carburetor system (1 liter gasoline for 43.2 minutes). I introduced the carburetor infront of the reactor near to air mixed valve, and the electricity directly connected to home plug for daily consumption. |
 | Motorcycle Running on Plasma Ignition Here we go. I try 4 stroke Yamaha 113 cc Matic gasoline engine running on plasma ignition (S1R-Tero circuit). I used 47 uf 250 Volt, 600 watt 220 volt output UPS as power source,35 A full wave bridge rectrifier, 16 pcs 1N5408 diodes on each side, and 100% gasoline on engine. The motorcyle runs very smooth. Later I will try to ride this motorcyle with this plasma ignition system to look what improvement will I get (better milleage, power boost, or anything else ???) |
 | water plasma engine My first video of the construction of the water plasma engine, water fuel generator and plasma burner tube. |
 | Water spark plug My replication of the gotoluc process of spark enhancing. The close up shots I do not do twice each, even though that is what I say, bad editing.. And this was with wet contacts already. I was messing around with the water spray before I started filming, and there was still water on the contacts. |
 | Water Sparkplug | Plasma Ignition| Booster Caps Booster caps in parallel to plug as low voltage source. Golf ball size bursts that could not be captured by film |
 | Plasma spark, no water Plasma plug, 240ac from generator into voltage doubler = 450v being discharged into spark gap from ignition coil. |
 | Plasma Spark-Tero's circuit This video is the response to energeticforum.com that present worked Tero's circuit on my previous video. Sorry for bad shoot video. I used one hand to hold camera and other to start the engine. It's difficult to take the video with tripod, but the main purpose is to take the plasma effect motion which some time hard to catch by digital camera. And that's it. |
 | #4 HHO Dual anode Plasma spark plug prototype HHO Dual anode Plasma spark plug prototype. It was a Champion CJ8 plug out of a 16hp electric start lawn mower engine. We busted out the inside to make way for the new anode test tubes. The electrical tape and rubber hose will not hold up in the cylinder but it will work fine for a few bench tests (which we'll post after we get some videos). Thank you 'gotoluc' and all the other youtubers that have been working on the new spark plug designs. Click the link below for more videos here or check ... |
 | Plasma Ignition (Vexus) on SUV Today I completed the test of Vexus Plasma Circuit on 2400 cc SUV engine. I connected it to all (4) cylinders. Begins on 500 RPM (idle) up to 3000 RPM with no misfire. I have increasing from 500 RPM (original ignition) to 650 RPM (plasma booster) in idle mode. |
 | RV 2HP 3 PH Motor-Test Load Today I tried to put loads to last RV setup on 2 x 2 HP 3 PH motor. When I put a 500 watt ML to the alternator side, the voltage remain goes down to 150 volt from 465 volt and the light only about 80-90% compared to the original brightness . With a 850 watt grinder as a load I feel the speed goes down to around 90% compared to the original grinder speed. |
Popular searches: Cuba, Scuba Diving, Skydiving, Dubai, Niagara Falls, Rainforest, Surfing, Snowboarding, Sandboarding, Pyramids, Everest, Stonehenge, Bear Grylls
