العربية
中国
Français
Deutsch
Ελληνική
हिन्दी
Italiano
日本語
Português
Русский
Español
Title:
How to Drill & Tap
Description:
From "Dull Knife Productions" Hey all, I had a few folks ask me how I made the threads for my elbow connectors into my cell. Well your in luck cause here is a vid showing how I do it. I hope this helps. AH p.s. BTW when you get more experience with this, you will find what drill bit & tap sizes you need to use with whatever specific threaded elbow you use. Again this is just the "dull knife" way of getting it done.
Author:
AlmostHydrogen
Tags:
AlmostHydrogen, HHO, cell, booster, how, to, drill, and, tap, elbow,
How to Drill & Tap
Description:
From "Dull Knife Productions" Hey all, I had a few folks ask me how I made the threads for my elbow connectors into my cell. Well your in luck cause here is a vid showing how I do it. I hope this helps. AH p.s. BTW when you get more experience with this, you will find what drill bit & tap sizes you need to use with whatever specific threaded elbow you use. Again this is just the "dull knife" way of getting it done.
Author:
AlmostHydrogen
Tags:
AlmostHydrogen, HHO, cell, booster, how, to, drill, and, tap, elbow,
Popular searches: Cuba, Scuba Diving, Skydiving, Dubai, Niagara Falls, Rainforest, Surfing, Snowboarding, Sandboarding, Pyramids, Everest, Stonehenge, Bear Grylls
Related Videos:
 | Burnt HHO Plates 1 Burnt HHO Plates 1 |
 | Drill and tap holes into steel pipe for wind turbine www.elperfecto.com A steel pipe coupling gets drilled and tapped with titanium nitride coated drill and plug tap. Eye bolts are attached to the pipe through these drilled holes. Guy wires will be attached to the eye bolts, to secure a wind turbine to its pole. This video documents one of the construction steps of a wind turbine at elperfecto.com. The next step of this wind turbine construction: www.youtube.com The full documentation of this wind turbine construction: www.elperfecto.com... |
 | How To Properly Drill Into Metal More Videos @ www.rccaraction.com RC Car Action Magazine Editor Kevin Hetmanski shows how to drill holes in any material. |
 | #08-027 Building a Hydrogen Exaust Hood I spend the better part of two days pretending I know what I'm doing as I consruct a hydrogen exhaust hood for my HHO experiments. |
 | Tapping Attachment 2 tapping holes from 10-32 to 1/2-13 threads |
 | Wiring diagrams for HHO Cells Since I dont know much about installing these cells, I have been doing some reading on it. Anyway here is some info I hope will help others like me in regards to wiring & what goes where when it comes to cell wiring & installation. Steve ps This is for informational purposes only - so if you blow up your vehicle, its not my fault ;) |
 | Power Tools & Carpentry Skills : How to Use a Tap & Die Set Using a tap and die set creates threaded holes and threaded bolts that can be used in wood working and manufacturing. Make or repair bolts and fit them into custom-threaded holes by using a tap and die set like an experienced builder with the instructions in this free video on carpentry tools. Expert: Robert Markey Bio: Robert Markey earned his BS in Physics from MIT in 1969 and his MS in Computer Science from the University of Massachusetts in 1982. Filmmaker: equilibriofilms Erik... |
 | First Lathe Part! Includes Threading! Making my first part on my 7x14 Mini lathe. Includes parting off stock, turning, facing, chamfering, drilling, tapping and threading! Visit www.nyccnc.com for more! |
 | What Wires should I use?!?!?! Yea I'm starting to look at what I need to install my cell, like what kind of wires do I use? Well I dont have all the answers, but I am getting closer. Check out this vid and see if it doesnt make some sense. AH ps btw if I am wrong and you have the right info, let me know so I can make corrections; IOW I dont want to set anyone up for failure. pps all information is for educational purposes only - IOW I am not liable for anything you do or do not do. ;) here is the link to the table... www ... |
 | TBC 60 - Hydraulic Fitting Application Ergomat TBC Multi Slide Lathe producing a hydraulic fitting from round bar stock. The application shows polygon milling, cross drilling, Tapping, and thread chasing, milling and end milling |
Popular searches: Cuba, Scuba Diving, Skydiving, Dubai, Niagara Falls, Rainforest, Surfing, Snowboarding, Sandboarding, Pyramids, Everest, Stonehenge, Bear Grylls
