العربية
中国
Français
Deutsch
Ελληνική
हिन्दी
Italiano
日本語
Português
Русский
Español
Title:
DIY CNC Test of the stepper motors
Description:
I connect two steppers (X and Y axis) to the controller, and play a little with that. So far it looks that will do the job.
Author:
ultralajt
Tags:
DIY, CNC, stepper, test,
DIY CNC Test of the stepper motors
Description:
I connect two steppers (X and Y axis) to the controller, and play a little with that. So far it looks that will do the job.
Author:
ultralajt
Tags:
DIY, CNC, stepper, test,
Popular searches: Cuba, Scuba Diving, Skydiving, Dubai, Niagara Falls, Rainforest, Surfing, Snowboarding, Sandboarding, Pyramids, Everest, Stonehenge, Bear Grylls
Related Videos:
 | First run of DIY CNC This machine is a small PCB sized milling and drilling machine. The spindle is custom built and uses a scaled down version of an R8 collet. It will be an automatic tool changing spindle once I get the tool rack made. The spindle runs at 24000 RPM. Rapids of the machine are only 600 IPM at this time as I only have a 35 volt power supply for the steppers. General specs are: Accepts 1/8" shank tools 24000 RPM spindle 20 tool capactity Auto tool length measuring 9.5" X travel 15.5" Y travel 3.5 ... |
 | DIY CNC Allmost serious test This video shows one of the first tests performed on my completetd machine. I remove the table board, remove the dremell tool, and set Z axis to just 2 cm in order noto to go down too much and damage the machine. It looks that it works as expected, so next step will be a real test with cutting in to the foam plate. If this test will be OK, then I will go for a balsa wood carving. |
 | DIY CNC -Gantry first assembly Roughly assembled and playing.... |
 | DIY CNC First engraving of the balsa wood The machine is allmost finished! Last evening, I test cut a balsa wood. I set speeds low as I dont have a proper tool yet. |
 | DIY CNC -Gantry test assembly Just clamped together provisorry to see if there are chance that this will work. It looks it will serve for its use on the gantry of DIY CNC Router. |
 | DIY CNC machine milling polycarbonate CNC machine milling robot parts from polycarbonate. |
 | Rumorella at work on a plastic case My homebrewed CNC mill is cutting a plastic box designed to contain an electronic circuit. This was the first time I put the powertool horizzontally. |
 | Homemade CNC Router - 2d Drawing Test The CNC is very nearly complete, at least functionally, everything that I add from here on out is for ease-of-use (enclosure, vacuum shroud, cable tracks, soundproofing, etc). Here is a simple 2d drawing test that I did to make sure everything works fine with the z-head and router attached. I would have cut something but I don't have any endmills, those should be shipping tomorrow (gotta love mcmaster-Carr). I did get an overhead light for the garage, unfortunately it didn't have mounting ... |
 | Homemade CNC Christmas Ornament 2008 - Neo7cnc.com My "How it's made" of the Christmas Ornament 2008 using bobcad v23, ncplot v2 and Mach3 with homemade CNC router. |
 | GUPPY 2 shrt Shortened video clip of GUPPY 2 first flights. |
Popular searches: Cuba, Scuba Diving, Skydiving, Dubai, Niagara Falls, Rainforest, Surfing, Snowboarding, Sandboarding, Pyramids, Everest, Stonehenge, Bear Grylls
